Selection Of Lightning Protection Devices For Communication Lines
Home » Solution » Solution » Automotive System » Selection Of Lightning Protection Devices For Communication Lines

Selection Of Lightning Protection Devices For Communication Lines

Views: 0     Author: Site Editor     Publish Time: 2023-10-30      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

profile

 

The communication line lightning protection is installed on the PCB in series. Therefore, when selecting lightning protection devices, it is necessary to ensure that the lightning protection devices can play a protective role, and at the same time, the matching problem of the lightning protection devices and communication lines must also be considered. Therefore, the following three points should be mainly considered when selecting lightning protection devices:

 

1

Voltage level problem

2

Rate matching problem

3

Device installation issues

 

Lightning protection is becoming more and more important for highly integrated and sophisticated electronic equipment and data transmission. Yint Electronic Devices can provide comprehensive lightning protection solutions. In order to illustrate different practical applications, the actual protection is divided into three categories:

  • Basic protection level

Designed according to IEC61644-1 (Draft1997), it is used to discharge lightning current and is the first level of protection. It is installed at the cable entry point.

  • Comprehensive protection level

According to Class1+2+3 of IEC61644-21, as a sophisticated comprehensive protection, it can be designed directly at the front end of the equipment information input (such as the equipment is close to the cable entry point)

  • Fine protection level

It is mainly used to limit surge overvoltage. The distance from the basic protection level should be no less than 5m, and it is designed directly at the access end of the access chip or sensitive devices such as DSP and ARM.

1

 

communication line product device selection process

 

 

Environmental analysis of actual product use

A) Is the product placed outdoors?

Will there be any overhead introduction at the upper end?

1) If there is direct introduction, physical protection, lightning rods, shielded chassis, etc. should be considered.

 Voltage level selection

B) The selection of the maximum working voltage of communication equipment is determined based on the working voltage of communication. The working voltage of the protection device must be greater than 1.2 to 1.414 times the working voltage of the communication line on the equipment.

2) Refer to the technical parameters of various types of products in this book, including shutdown voltage, clamping voltage, and breakdown voltage.

Rate matching options 

C) Communication line lightning protection is designed on the equipment line. The maximum transmission rate it supports should be greater than the transmission rate of the communication line. Otherwise, it will cause communication interruption or increase in bit error rate, packet loss, and data loss, which is usually reflected in the device capacitance.

3) Mainly refers to high-frequency circuits or high-bandwidth equipment. Please refer to this book for relevant technical parameter selection.

 

 

Relevant standards suitable for product equipment

D) Communication products have different requirements in different countries. In addition, there is a relevant standard level that the product wants to reach.

4) Consider TIA-968-A (FCC Part68), UL1950, UL1949, ITUK.21, Telcordia Gr-974 and other industry standards. Chinese standards: "Communications Industry Standard of the People's Republic of China".
 

Device size and installation location 

E) Consider the size of the device, whether the PCB is easy to install, whether the installation location is close to a heat source or other harsh conditions, whether high-frequency vibration is required, etc.

5) The overall structural layout of the product should be adjusted accordingly to best suit the characteristics of the product.
 
selection of voltage level

 

The selection of the highest working voltage of the protection device on the communication line is determined based on the working voltage of the data communication line. It is an important parameter for selecting protection devices, but there is no common standard in practical applications. The working voltage of the protection device should be greater than the line communication voltage. (Attached is the working voltage of commonly used communication lines, for reference only, there are still differences between different chip manufacturers)

 

Communication line type

video cable

RS422RS485

RS232

Ethernet over Coax

100M

Ethernet

Analog telephone line/ADSL

2M digital relay

XDSL

DDNX 25/frame relay

ISDN

Rated work

Voltage(V)

<6

<5

<12

<5

<5

<90

<5 or<12

<6

<6 or

<40~60

<40

General rate BPS

 

2M

 

10M

100M

<2M

2M

8M

2M

2M

Lightning protection device

Operating Voltage

6.5

6

18

6.5

6.5

180

<6.5or<18

18

18 or 80V

80

Interface Type

BNC

ASP/SD

SD

RJ

RJ

RJ

BNC RJ45

ASP RJ45

ASP RJ45

RJ

 

some domestic standards

 

GB50057-1994

Design Code for Lightning Protection of Buildings

GB50343-2004

Technical specifications for lightning protection of building electronic information systems

YD5098-2005

Design specifications for lightning protection and grounding engineering of communications bureaus (stations)

YD/T1235.1/2002

Technical requirements for surge protectors for low-voltage power distribution systems in communications bureaus (stations)

YD/T1235.2/2002

Test method for surge protectors used in low-voltage power distribution systems of communications bureaus (stations)

DL548-94

Lightning protection operation and management regulations for power system communication stations

GA173-2002

Computer information system lightning protection security device

GA267-2000

Safety Protection Specification for Lightning Electromagnetic Pulse in Computer Information Systems

TB/T3074-2003

Technical conditions for lightning electromagnetic pulse protection of railway signaling equipment

TB/T 2311-2002

Lightning protector for railway electronic equipment

YD/T993-2006

Lightning protection technical requirements and experimental methods for telecommunications terminal equipment

 

 

 

 

 

 

Sign up for our newsletter
Subscribe

OUR PRODUCTS

ABOUT US

Leave a Message
Leave Us Your Info

MORE LINKS

CONTACT US

F4, #9 Tus-Caohejing Sceience Park,
No.199 Guangfulin E Road, Shanghai 201613
Phone: +86-18721669954
Fax : +86-21-67689607
Email: global@yint.com.cn

SOCIAL NETWORKS

Copyright © 2024 Yint Electronic All Rights Reserved. Sitemap. Privacy Policy. Supported by leadong.com.